The content below about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround is really intriguing. Don't bypass it.
Setting up a bath tub isn't precisely rocket science, yet it does need solid plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old bath tub with a new one is additionally a moderately hard job. If the old tub is easily accessible, the task can move easily; if you need to open up a wall surface to get rid of the old bathtub as well as place the brand-new bath tub, the job is a lot harder. In either case, the project is within a residence handyman's abilities, although you will certainly require an assistant to leave the old bathtub as well as set in the new one. Ensure you have certified yourself for the task and fit attempting it. Rather than hiring a specialist to take control of a halfway-completed task, it is far better to consider employing one prior to you start. Opportunities are you might require an expert plumber to make tube connections.
This short article will aid you mount a brand-new tub in your restroom if you have currently acquired a new tub and also do not need to change the setup of your previous water system pipes.
Your tools and also material list must comprise the following:
Preparing for the Installation
Firstly, the sustaining frame provided with the bath ought to be fitted (if needed) according to the supplier's directions. Next off, fit the faucets or mixer to the tub. When fitting the faucet block, it is important to make sure that if the tap features a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is additionally sensible to fit a supporting plate under the taps device to stop strain on the tub.
Fit the adaptable faucet connectors to the bottom of both faucets making use of 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Use the nut provided by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. Ensure you make use of every one of the supplied washers.
Connect the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link all-time low of the overflow tube in a comparable manner.The bath ought to currently prepare to be suited its final placement.
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your installment, after that the first thing you need to do is separate the supply of water. After doing so, turn on the taps to drain any kind of water remaining in the system. The procedure of getting rid of the existing faucets can be rather problematic due to the limited gain access to that is commonly the situation.
Use a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipelines to the taps. Have a towel prepared for the remaining water that will certainly come from the pipelines. Once the supply pipelines have actually been removed, use the same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single faucets from transforming during this procedure. As soon as the faucets have actually been eliminated, the holes in the bath/basin will have to be cleaned up of any kind of old sealing substance.
Prior to proceeding to fit the brand-new faucets, compare the pipeline links on the old faucets to the brand-new taps. If the old taps are longer than the new taps, then a shank adapter is required for the new taps to fit.
Setting up the Bath tub
Making use of both wood boards under its feet, put the tub in the needed setting. The wooden boards are practical in uniformly spreading the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto four small factors.
The following goal is to ensure that the bath tub is leveled all round. This can be attained by examining the level and changing the feet on the bath tub up until the level reads level.
To install taps, fit all-time low of the furthest adaptable tap adapter to the proper supply pipeline by making a compression join; then do the exact same for the other tap.
Switch on the water supply and examine all joints as well as new pipework for leaks and tighten them if necessary. Fill up the tub as well as additionally inspect the overflow electrical outlet as well as the regular outlet for leaks.
Finally, take care of the bathroom paneling as defined in the manufacturer's instruction manual. Tiling and sealing around the bathtub ought to wait until the bathtub has been used at least when as this will certainly resolve it right into its final position.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will certainly require a plastic connector to prevent damages to the thread. One end of the connector fits on the plastic tail of the faucet as well as the other end provides a link to the existent supply pipelines.
If you need to fit a monobloc, after that you will require minimizing couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, place the faucet in the placing hole in the bath/basin ensuring that the washers are in area between the faucet as well as the sink. Safeguard the tap in position with the maker supplied backnut. When the tap is safely in position, the supply pipelines can be linked to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with typical tap ports. The previous kind must be attached to the faucet finishes initially, tightening up just by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Bath tub
In the location where the bath meets the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is very important as the fitting can move sufficient to split a rigid seal, causing the water to penetrate the wall surface between the bathroom and the tiling, bring about problems with wetness and feasible leaks to the ceiling listed below.
You can choose from a selection of coloured sealers to assimilate your components as well as installations. They are offered in tubes as well as cartridges, as well as can securing spaces as much as a size of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with spins of drenched paper or soft rope. Remember to constantly fill up the bathtub with water prior to sealing, to enable the activity experienced when the tub is in use. The sealant can break relatively very early if you do not think about this activity prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally quickly offered on the market. It is advisable to fit the floor tiles utilizing water-resistant or waterproof glue as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Hopefully you liked our excerpt about How to Install a Bathtub Yourself. Thanks so much for spending some time to read through our content. Make sure you take the opportunity to promote this write-up if you enjoyed reading it. We treasure reading our article about Tools You Need to Install a New Bathtub .
Leak-free future? Call.